vwbusman66
Stößelstange über alles
- Joined
- Oct 12, 2016
- Location
- SE MI
Did you complete the challenge yet?
-
Hello Guest, welcome to the initial stages of our new platform!
You can find some additional information about where we are in the process of migrating the board and setting up our new software hereThank you for being a part of our community!
MountainMeet 5.0, September 25-29, 2019
- Thread starter propav8r
- Start date
Did you complete the challenge yet?
Wren
Porkchop Sandwiches
- Joined
- Jun 29, 2006
- Location
- Athens, GA
Man, you're out of the loop.
vwbusman66
Stößelstange über alles
- Joined
- Oct 12, 2016
- Location
- SE MI
Had to check FB. Kudos to you.
propav8r
F*ck Edgar
- Joined
- Jan 17, 2010
- Location
- Franklin, NC
I need to get started on a decal design so Dana has time to cut them before the last minute.
propav8r
F*ck Edgar
- Joined
- Jan 17, 2010
- Location
- Franklin, NC
Done.
vwbusman66
Stößelstange über alles
- Joined
- Oct 12, 2016
- Location
- SE MI
What about t shirts?
EDIT: See group buy page
EDIT: See group buy page
Last edited:
vwbusman66
Stößelstange über alles
- Joined
- Oct 12, 2016
- Location
- SE MI
Shirt link here!
http://forums.turbobricks.com/showthread.php?t=350331
http://forums.turbobricks.com/showthread.php?t=350331
Wren
Porkchop Sandwiches
- Joined
- Jun 29, 2006
- Location
- Athens, GA
You misspelled Meat again.
mikep
Vintage Ride
- Joined
- May 24, 2003
- Location
- 38? 27' N 75? 29' W
I?ll bring the fried chicken.
propav8r
F*ck Edgar
- Joined
- Jan 17, 2010
- Location
- Franklin, NC
Bring? You must be unfamiliar with Wren's Fryer of Doom
boostdemon
creative mastermind
- Joined
- May 31, 2002
- Location
- Cary, NC
propav8r
F*ck Edgar
- Joined
- Jan 17, 2010
- Location
- Franklin, NC
not gonna lie, that thing scares me a little bit.
Yeah...it'll be set up not on the porch this year.
Wren
Porkchop Sandwiches
- Joined
- Jun 29, 2006
- Location
- Athens, GA
It's a tater tot's worst nightmare.
.
.
Last edited:
vwbusman66
Stößelstange über alles
- Joined
- Oct 12, 2016
- Location
- SE MI
Can we get a pic of that, for those of us uninitiated?
Wren
Porkchop Sandwiches
- Joined
- Jun 29, 2006
- Location
- Athens, GA
200K BTU
<iframe width="560" height="315" src="https://www.youtube.com/embed/6j0VxJncSqA" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>
<iframe width="560" height="315" src="https://www.youtube.com/embed/6j0VxJncSqA" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>
vwbusman66
Stößelstange über alles
- Joined
- Oct 12, 2016
- Location
- SE MI
o fuk
propav8r
F*ck Edgar
- Joined
- Jan 17, 2010
- Location
- Franklin, NC
The main body of the fryer is a 240 steel wheel. Which might explains why it leaks oil.
- Joined
- Dec 25, 2002
- Location
- mont, AL
ol roadracer4life chatting in the background there
propav8r
F*ck Edgar
- Joined
- Jan 17, 2010
- Location
- Franklin, NC
"Yeah we were just talkin' about that" lol
propav8r
F*ck Edgar
- Joined
- Jan 17, 2010
- Location
- Franklin, NC
So planning the drive for this year...last year was about 110 miles/3.5 hours. I think that felt a little long.
I keep saying that I'm gonna spend more time relaxing on Saturday one of these years, and I think this year will be it. Planning on a 50-60 mile route that just hits some stuff closer to the lodge.
That cool?
I keep saying that I'm gonna spend more time relaxing on Saturday one of these years, and I think this year will be it. Planning on a 50-60 mile route that just hits some stuff closer to the lodge.
That cool?