Search results

Looking for a part number for the small o-ring that goes around the banjo bolt to secure the oil cooler elbow to the block? In the middle of resealing the oil cooler, and there is no o-ring to even reuse? This is on a 93 945ti. Thanks again, Bret.

Hello all, I got a 75 242. The question is which kickdown cable should I use to put an AW71 in my 75? I seem to find nice GEMO brand ones for the turbo cars. Are these sufficient to work in my 75? Thanks in advance. P.S. I could not afford a T5 swap so thats why AW71. Just about done...

Hey TB peepz, Been awhile since I have thrown a shindig so here goes. The plan is to meet and greet at my place. 859 Byron Dr. South San Francisco Plan a nice drive down the coast a way. Then wrenchin beers, fat BBq and evening bonfire. Who is down? I have plenty of space for people to...

From experience who has run the D cam, in a NA? With adjustable cam gear? Advanced, retarded? I am planning on putting one in my brick. It is an auto to boot..:oops:

Lookin at Rock auto for plug wires for my new 86 244. Anyone have any experience with Ngk? I like there plugs. $33 for the set is not bad. Bret

Got a 96 850 na here at the shop. I am in the process of replacing all of the cooling system hoses and such. I removed the plastic firewall passthrough for the heater hoses. Unfortunately i dont seem to have the proper arrangement of o rings and spacers on the engine bay side of the plastic...

Soo me and the lady picked up 122powers 242. The car is slowly getting a stage 0. Replaced cap n rotor plugs did a LOF. Also changed the fuel filter. Up untill the filter change the car was running pretty good. Now it stumbles at higher rpm and feels gutless in general. I know i need a...

Hello all you brickers. I have a bit of a problem with my 91 NA 245. I am in the midddle of rebuilding a B230ft and I had a set of injectors out of a lpt 850. I grabbed them at pic n pull and wanted to make sure they worked ok. I knew the car would bog down at idle, decel or anytime I wasn't...

http://flic.kr/p/e7KBH7 Squirter to crank clearance..

So i got some Koni yellow struts gonna run em with 10" 325# springs. What is the most spring these struts can handle? Bret

Looking on FCP's website they stock a meyle front strut mount for the 240. Is it any good or should I pony up and go to the stealership? I know Uro and scamteck are junk but what about Meyle? Bret

How to make them work together? (91 245) I know earlier housings will work but I want to make my housings work with the Decarbon's. The current strut housings do not allow the gland nut to engage threads on the housing. I may grind off some metal on the bottom of the insert? Thoughts?

Installing Yoshifab intake spacer's. Should I use 1, 2 or no intake manifold gasket's? :) Thanks, Bret

Installing Yoshifab intake spacer's. Should I use 1, 2 or no intake manifold gasket's? :) Thanks,' Bret

I got an old 240 with broken door handles. The real problem is the door's are closed. How do I remedy this.:oops:

Hey I was wondering the compressed and extended length of a 240 rear shock? I am going to try out some of Jerd's budget shocks and need to hobble together a setup.:)

I am getting a new of tires for the Hyrda's I am picking up this weekend.:) What would be better choice from an agressive driver standpoint. I am even willing to do 205 if the benefits are a beefier sidewall with less flex. I want the wider contact patch but not if the tradeoff is...

Hey All, Wanted to know if LH 2.2 primes the pump when in Key on position 2? Not cranking or running. Thanks Bret

So I am diagnosing a stalling issue on an 88 740. The question is setting up the pressure tester. This fuel rail has no provision for a schrader valve, and ALLDATA suggests using a few fittings and "T" ing off that. I was trying to reduce parts to buy in order to test.. It seems possible to...

Well it's been forever, since 07 I have been on this sight with no project thread. Now is the time. Just got the internet hooked up, and my free computer working great. Car was purchased in 08. Picked it up in Healdsburg Ca. Its had 169k on the clock. Picked it up for the steep price of...