home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 50 of 300
Search took 0.02 seconds.
Search: Posts Made By: Lankku
Forum: performance & modifications 07-13-2021, 03:51 PM
Replies: 78
Views: 33,362
Posted By Lankku
I'd have a small reccess machined in to the stock...

I'd have a small reccess machined in to the stock pulley to center the SC pulley. Also welding cast and steel together on a place like that should be done properly.
Forum: performance & modifications 07-11-2021, 04:42 PM
Replies: 78
Views: 33,362
Posted By Lankku
Solid. This is a reference to that: ...

Solid. This is a reference to that:






Many use a solid pulley in racing without issues. I'd rather have a damper but on a B2xx it's easier to have a solid pulley with a SC.
Forum: performance & modifications 07-11-2021, 06:35 AM
Replies: 78
Views: 33,362
Posted By Lankku
Not much to see. Here is a pic when I lifted the...

Not much to see. Here is a pic when I lifted the engine for a H-beam swap. Bought the SC used as a kit with bracket.
...
Forum: performance & modifications 07-03-2021, 12:09 PM
Replies: 18
Views: 2,878
Posted By Lankku
As far as I know he is using MS3 Pro and custom...

As far as I know he is using MS3 Pro and custom cams. Lift should be around 10.5mm, can't really remember. He's used 10.5mm lift in milder engines so this could have more.

For the deck I recall he...
Forum: performance & modifications 03-21-2021, 09:01 AM
Replies: 6
Views: 2,678
Posted By Lankku
With 0 you will need to cut the rear fenders. I...

With 0 you will need to cut the rear fenders. I would go with ET 20-25 and even then you might have to trim the lip.
Forum: projects & restorations 02-22-2021, 04:27 PM
Replies: 148
Views: 161,577
Posted By Lankku
In the beginning of January -92 got 144 rear door...

In the beginning of January -92 got 144 rear door window frames for added lightness. Took some drilling and time to make them fit. Two bolt holes were on the same place as original spot welds. 2.6kg...
Forum: maintenance & nonperformance 02-22-2021, 12:26 PM
Replies: 27
Views: 4,227
Posted By Lankku
I'm assuming the fuel pumps(K-jet copy) took...

I'm assuming the fuel pumps(K-jet copy) took 10-15A. Coils around 10A because it's just two coils firing at a time and low load/rpm. Injectors and ECU might be around 10A combined. That makes around...
Forum: maintenance & nonperformance 02-21-2021, 06:41 PM
Replies: 27
Views: 4,227
Posted By Lankku
A good and fully charged battery will take you...

A good and fully charged battery will take you further than 20 miles. But why risk it if it's not a must.


Then it has not been working properly for a while.

Battery on the "B6284T" ran out...
Forum: maintenance & nonperformance 02-14-2021, 03:03 PM
Replies: 5
Views: 1,177
Posted By Lankku
No chain driven engines in those. Got to be...

No chain driven engines in those. Got to be something really special if it has.
Forum: maintenance & nonperformance 02-12-2021, 08:03 PM
Replies: 3
Views: 1,230
Posted By Lankku
700/900/850/x70I 2-speed fan relay is ground...

700/900/850/x70I 2-speed fan relay is ground controlled and has constant 12V. Full speed takes around 30A when it's switched on directly. Depending on stuff it's a bit under or over. So if low speed...
Forum: maintenance & nonperformance 02-10-2021, 12:28 PM
Replies: 7
Views: 1,776
Posted By Lankku
Behr is the original make. What were/are the...

Behr is the original make.

What were/are the symptoms? If it just stopped the resistor might be bad.
Forum: maintenance & nonperformance 02-07-2021, 08:00 AM
Replies: 1
Views: 1,235
Posted By Lankku
Only trunk has rubber plugs. Floors have glued...

Only trunk has rubber plugs. Floors have glued solid metal plates.
Forum: performance & modifications 02-03-2021, 04:49 PM
Replies: 68
Views: 10,088
Posted By Lankku
Years ago I thought of making a flat undertray...

Years ago I thought of making a flat undertray but then gave up. It has surfaced on my mind every now and then. Lately have thought of making just two simpel panels before the rear axle. That way the...
Forum: performance & modifications 02-03-2021, 04:30 PM
Replies: 78
Views: 33,362
Posted By Lankku
If you use waterpump for supercharger I'd say you...

If you use waterpump for supercharger I'd say you toast waterpump bearings much faster than you change timing belts. The belt(s) need to be tight. Even a stock 6PK serpentine needs to be tight.
...
Forum: performance & modifications 02-01-2021, 07:17 PM
Replies: 68
Views: 10,088
Posted By Lankku
https://lankku.kuvat.fi/kuvat/245%20GL%20-90/76.jp...

https://lankku.kuvat.fi/kuvat/245%20GL%20-90/76.jpg?img=medium
https://lankku.kuvat.fi/kuvat/245%20GL%20-90/Laitot%202015/27.jpg?img=medium

It's not that low, around the same level as...
Forum: performance & modifications 01-31-2021, 05:20 PM
Replies: 68
Views: 10,088
Posted By Lankku
Lip itself is enough for stabilizing the whole...

Lip itself is enough for stabilizing the whole car, didn't notice a big difference with the tray. Made the lip mostly for standing mile/track use. Also wagon roofline might be better for airflow...
Forum: performance & modifications 01-28-2021, 06:17 PM
Replies: 14
Views: 2,745
Posted By Lankku
https://www.mtecbrakes.com/

https://www.mtecbrakes.com/
Forum: maintenance & nonperformance 01-24-2021, 11:16 AM
Replies: 5
Views: 1,741
Posted By Lankku
Looking from front to back the fill plug is on...

Looking from front to back the fill plug is on the right side of the driveshaft flange, pointing forwards.
Forum: maintenance & nonperformance 01-21-2021, 12:57 PM
Replies: 10
Views: 2,975
Posted By Lankku
On a 140/240 yes, but the picture is from a...

On a 140/240 yes, but the picture is from a 700/900 and on those it's on the passenger side.
Forum: performance & modifications 01-17-2021, 07:41 AM
Replies: 26
Views: 19,780
Posted By Lankku
XC90 discs are a direct fit. I didn't do anything...

XC90 discs are a direct fit. I didn't do anything but slap them on front and rear.
Forum: performance & modifications 01-15-2021, 08:19 PM
Replies: 3
Views: 2,217
Posted By Lankku
Now that I've read more looks like I missed some...

Now that I've read more looks like I missed some things with the heads. One of them is thermostat location. N and RN have the housing in the head but RNC has a plastic housing in the block. So at...
Forum: performance & modifications 01-15-2021, 02:39 PM
Replies: 3
Views: 2,217
Posted By Lankku
I'd say the head fits on top of a N block just as...

I'd say the head fits on top of a N block just as a RN head or vice versa.

Some info compared to RN: http://volvospeed.com/vs_forum/topic/164042-rn-vs-rnc/

RNC uses the same timing belt kit as...
Forum: maintenance & nonperformance 01-12-2021, 06:22 PM
Replies: 6
Views: 1,973
Posted By Lankku
You need only the left side bracket and bolt for...

You need only the left side bracket and bolt for the clutch pedal. Otherwise it's the same.
Forum: maintenance & nonperformance 01-08-2021, 07:06 PM
Replies: 4
Views: 1,640
Posted By Lankku
1270mm is listed for manual with AC. 1250mm for...

1270mm is listed for manual with AC. 1250mm for automatic without AC.
Forum: performance & modifications 01-08-2021, 05:17 PM
Replies: 59
Views: 19,148
Posted By Lankku
Spartan is so rough in tight corners that...

Spartan is so rough in tight corners that many(myself included when I tried one) have moved on to Truetrac or other solutions. Also it creates a lot of play on to the driveshaft movement, really nice...
Forum: performance & modifications 01-08-2021, 05:07 PM
Replies: 18
Views: 4,030
Posted By Lankku
It'll hold 400hp with forged rods only....

It'll hold 400hp with forged rods only. Everything else is extra.

LH2.4 can do it if you have a good tuner or can tune it yourself.
Forum: maintenance & nonperformance 01-06-2021, 04:29 PM
Replies: 8
Views: 1,968
Posted By Lankku
Looks like it's included in the housing:...

Looks like it's included in the housing: https://www.skandix.de/en/spare-parts/electrics/control-units/housing-control-unit-stalk-indicators-wipers/1038324/
Forum: maintenance & nonperformance 01-06-2021, 04:17 PM
Replies: 4
Views: 1,640
Posted By Lankku
Yes. It should be 6PK 1250.

Yes. It should be 6PK 1250.
Forum: performance & modifications 01-05-2021, 09:04 AM
Replies: 31
Views: 9,132
Posted By Lankku
FK and FT are same engines just with different...

FK and FT are same engines just with different boost.
Forum: projects & restorations 12-30-2020, 04:22 PM
Replies: 148
Views: 161,577
Posted By Lankku
Yesterday installed spacers and new brake pads to...

Yesterday installed spacers and new brake pads to the front. Wheel still fits nicely inside the fender liner.

https://lankku.kuvat.fi/kuvat/245%20-92%20Bxxx/Laitot%202020/59.jpg?img=medium
Forum: projects & restorations 12-28-2020, 03:35 PM
Replies: 148
Views: 161,577
Posted By Lankku
Finally weather was good enough and I had time to...

Finally weather was good enough and I had time to take a couple of shots outside. You have to look for a while to be able tell that body has changed. Which is good :)
...
Forum: performance & modifications 12-24-2020, 08:51 PM
Replies: 26
Views: 8,103
Posted By Lankku
Rubbing depends on your wheels and tires. I'd cut...

Rubbing depends on your wheels and tires. I'd cut the fender lip where needed. That's also what the manual for original 20mm spacers says. Just dont cut the spot welds out or you have to do some new...
Forum: maintenance & nonperformance 12-23-2020, 04:06 PM
Replies: 9
Views: 1,872
Posted By Lankku
If Hall wiring is mixed or shorted it might mess...

If Hall wiring is mixed or shorted it might mess the 5 volt regulator and there is no life on the board. Recently had troubleshoot a MS2 V3 because of this.

So measure that you have both 5 and 12V...
Forum: performance & modifications 12-23-2020, 03:16 PM
Replies: 15
Views: 3,136
Posted By Lankku
My solution is easy because I use a M90 and...

My solution is easy because I use a M90 and therefore no pilot bearing.

It could be that the crank is a 0.1-0.2mm bigger and that's why the bearing is loose?

You could use a (roller)bearing...
Forum: projects & restorations 12-21-2020, 06:40 PM
Replies: 148
Views: 161,577
Posted By Lankku
Recently bought a -87 745 Turbo which had a...

Recently bought a -87 745 Turbo which had a broken stock LSD and swapped in a newer rear axle with G80. Decided to use the old one as a base for the -92 axle swap. Had it sandblasted and got started...
Forum: projects & restorations 12-14-2020, 10:47 PM
Replies: 148
Views: 161,577
Posted By Lankku
Everything behind the transmission is stock. One...

Everything behind the transmission is stock. One piece driveshaft might not even fit without cutting the floor and would need a slip yoke.

Driveshaft is on it's third rear u-joint because of...
Forum: performance & modifications 12-14-2020, 06:45 AM
Replies: 3
Views: 1,616
Posted By Lankku
To me that doesn't look bad at all. If one/two...

To me that doesn't look bad at all. If one/two bolts can pull it down without excessive force then it's ok. But if you are really worried you could have it machined flat.
Forum: projects & restorations 12-13-2020, 09:38 PM
Replies: 148
Views: 161,577
Posted By Lankku
From the passenger seat it feels like it should....

From the passenger seat it feels like it should. Winter, winter tires and one tire fire aren't the best for testing the real performance ;-) Owner is in the process of installing/getting a LSD or...
Forum: projects & restorations 12-13-2020, 09:31 PM
Replies: 16
Views: 6,611
Posted By Lankku
Turbos fit fine as they are. The rear turbo inlet...

Turbos fit fine as they are. The rear turbo inlet pipe needs a sharp bend and/or a bit hammering of the firewall to fit.

My old 745 with a B6254 and T6 turbos:...
Forum: projects & restorations 12-11-2020, 06:43 PM
Replies: 148
Views: 161,577
Posted By Lankku
It's just natural, pipe size is way too small...

It's just natural, pipe size is way too small compared to what is needed. Especially the stock rear muffler is restrictive because it's not a straight through. My 965 B6254T made only 0.3bar boost...
Forum: projects & restorations 12-11-2020, 05:50 PM
Replies: 148
Views: 161,577
Posted By Lankku
"B6284T" found its way to the storage a while...

"B6284T" found its way to the storage a while back and I've been driving mostly the -92.

A bit on the side I've been aiding a 745 "T6" build, mostly getting it running and tuned with a MS2. After...
Forum: projects & restorations 12-11-2020, 04:54 PM
Replies: 16
Views: 6,611
Posted By Lankku
You can achieve easy 300hp with stock turbos and...

You can achieve easy 300hp with stock turbos and it'll be really nice to drive with a wide powerband. I'd say install a bigger turbo later on if/when you get bored with that.
Forum: performance & modifications 12-06-2020, 06:19 PM
Replies: 12
Views: 6,104
Posted By Lankku
850 injectors should be high impedance so the...

850 injectors should be high impedance so the resistor pack is not needed with those. I think they measure around 12ohm or so.
Forum: maintenance & nonperformance 12-06-2020, 03:46 PM
Replies: 8
Views: 1,541
Posted By Lankku
They fit right in. The rear bumper changed and...

They fit right in. The rear bumper changed and the hitch clears it without cutting the plastic. Doesn't affect the fitment on older cars.
Forum: maintenance & nonperformance 12-02-2020, 05:54 PM
Replies: 8
Views: 1,503
Posted By Lankku
Transmission oil heat exhanger inside the...

Transmission oil heat exhanger inside the radiator is known to leak. If that leaks then you'll also have coolant in the tranny. What does the transmission oil look like?
Forum: performance & modifications 11-27-2020, 05:06 PM
Replies: 3
Views: 1,475
Posted By Lankku
Wagon kit has rear sway bar mounting hardware...

Wagon kit has rear sway bar mounting hardware because often wagons don't have rear sway bar. That's the difference. A bit pricey pieces of steel you can get from a donor and a couple of bolts.
Forum: performance & modifications 11-25-2020, 06:32 PM
Replies: 3
Views: 1,901
Posted By Lankku
JT seems to offer catless dp....

JT seems to offer catless dp. https://martelius.com/en/products-by-car?automerkki=100&automalli=168
Forum: maintenance & nonperformance 11-25-2020, 01:43 PM
Replies: 7
240: drains
Views: 1,631
Posted By Lankku
Here you can see the front drain on the far left....

Here you can see the front drain on the far left. There is none in front of the jack point.

https://lankku.kuvat.fi/kuvat/240%20-84%20Hearse/19.jpg?img=medium
Forum: maintenance & nonperformance 11-16-2020, 06:00 PM
Replies: 14
Views: 4,270
Posted By Lankku
Engine bay cleans up alot if you even move the...

Engine bay cleans up alot if you even move the firewall part of the wiring inside. That's what I did with "B6284T" when I swapped the steering to left side. I did consider hiding it all but the sides...
Forum: performance & modifications 11-14-2020, 06:46 PM
Replies: 10
Views: 5,215
Posted By Lankku
Diameter is really close to 225/45/17 so I'd say...

Diameter is really close to 225/45/17 so I'd say it's a good size. Can't say about the fitment otherwise.
Showing results 1 to 50 of 300

 
Forum Jump

All times are GMT -4. The time now is 10:05 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.